1. Clean the surface properly by washing it off with Lacquer Thinners.
2. Wait 20-40 minutes for the Lacquer thinners to dry.
3. Depending on the surface you are painting you can either use a Paint Brush, Foam roller or Mohair roller.

( For large flat surfaces use a Mohair roller. For Kitchen cupboards a foam roller is better to use. ) paint a base coat in Stone Wash and allow to dry.

4. Ensure that your applicator is clean a dry and that the base coat has dried properly before you start painting on top of your base coat with White, Yellow or Red Tjhoko Paint colours.
5. Very important is to allow for each coat of paint to dry completely before applying the next coat.        

The post How to prepare your surface when painting with a Yellow, Red or White Tjhoko Paint on a dark surface. appeared first on Tjhoko Paint Switzerland.

Step 1 – Clean surface PROPERLY with Lacquer thinners (we use Powerfix Lacquer thinners). Wear gloves and work in a well-ventilated space.

Wait until the lacquer thinners is dry 20 – 40 minutes. I would then repeat the cleaning process again. (WE DON’T RECOMMEND TO PAINT ONTO A VARNISHED SURFACE IF THE SURFACE HAS BEEN VARNISHED WITHIN THE PAST 6 MONTHS. Varnish takes at least 6 months to cure. When painting onto an  enamel surface – contact us at support@tjhokopaint.co.za to give the right advice.)

Step 2 – Start painting. We recommend painting at least two coats. Very important when painting is to always allow a coat of paint to dry properly before the next coat of paint is applied. Depending on the colour being used a third coat would be necessary for example painting a white paint onto a darker surface.

The equipment you use for painting also plays a role.  A foam roller leaves a much thinner coat of paint than a paint brush. Therefore, more coats of paint would be required when working with a foam roller.

The paint does have a matt finish (Tjhoko Paint is a self-sealing, water-based, matt chalk paint) it does not need a sealant unless you have the piece of furniture outside or in a room like the kitchen or bathroom where there is lots of moisture. The Glaze makes the surface water and UV-Resistant. It also prevents stains and provides a more washable surface. We also recommend to seal tabletops and pedestal tops, kitchen, and bathroom wall tiles (painting in showers not recommended).

Step 3 – If you are applying the clear glaze, always allow the paint to dry for at least 4 hours before starting with the glaze application. In coastal areas or during winter months we recommend to only start glazing the next day (leave paint to cure overnight).

1. Dilute the Clear Glaze with 30% water (30ml of water for every 100ml of Glaze) or 3 parts Clear Glaze and 1-part water. (we recommend cooled, boiled water as it is less contaminated)

2. On darker Tjhoko colours we recommend 50/50 (1-part Tjhoko Clear Glaze and 1-part water. You can also use this ratio for a less sheen finish.)

3. Dampen a clean, colourless cloth with water and squeeze to remove all excess moisture. A Microfibre cloth works best.

4. Dip the cloth completely in the mixture to absorb the mix and then squeeze to remove excess moisture. 

5. Evenly wipe onto the painted surface. Work in a well-lit room to ensure that the entire surface is covered. If streakiness or lines occur – (it is caused by the fabric / cloth) just apply a second coat, half an hour later.
6. Should you wish to change colour or add paint techniques over the clear glaze, you can do so once it it has cured for an hour or longer.

Numerous DIY videos with steps are available on both our website and YouTube channel www.tjhokopaint.co.za and www.youtube.com/tjhokopaint

The post DILUTION OF CLEAR GLAZE ON DARK PAINTED SURFACES appeared first on Tjhoko Paint Switzerland.

In the areas that you have applied and used the rust converter you will also be washing the surface off ( this is all part of the instructions)

You would not need to then clean these washed areas with Lacquer thinners as the Rust Converter etches the surface and cleans it. Only the areas that you have not cleaned with the Rust Converter would require for you to clean with the Lacquer thinners.

The post How to treat a surface that has rust? appeared first on Tjhoko Paint Switzerland.

• Test a small area  to see if sanding would be needed in conjunction with the cleaning.
  • Clean a small area with Lacquer thinners  –  wait 20 minutes and paint your first coat –  allow to dry and then paint your second coat.
  • Wait for 24 hrs and then test by scratching the surface.
  • If the paint is removed by scratching we advise that  you sand first and then clean with Lacquer thinners –  this will make sure that the paint will grip onto the surface. Once you have  painted x2 layers and waited 24 hrs  –  repeat the scratch test again. If the paint  continues to be scratched off, a universal undercoat would then be need to be applied.
  • It is not uncommon for many enamel surfaces to pose a problem when painting on top of them.

• Sand with 100grit sandpaper.
• Clean well with Lacquer thinners and then start painting.
• Larger surfaces need to be tested before painting starts. ( As above)

The post Can I use Tjhoko Paint on an enamel surface? appeared first on Tjhoko Paint Switzerland.

The post Can I paint my outdoor furniture? appeared first on Tjhoko Paint Switzerland.

The post How do I use metallic paint? appeared first on Tjhoko Paint Switzerland.

The post How do I clean and prepare my surface before painting? appeared first on Tjhoko Paint Switzerland.

The post How do I prevent contamination of paint? appeared first on Tjhoko Paint Switzerland.

Secure the stencil using masking tape.  The masking tape secures the stencil but also allows a larger area to work on.

Move the stencil brush in a circular movement when applying it to the stencil. Holding the stencil down with your free hand.

The post How do I know if I am stencilling correctly? appeared first on Tjhoko Paint Switzerland.

Wash the item as directed on the tag. Pour any detergent used in the wash directly on the stain prior to placing it in the wash for extra stain removing power. Inspect after the cycle ends. If the stain is not completely removed, repeat this step until the stain is removed. Do not dry the garment until the stain has been removed. 

Bicarbonate of Soda can also be mixed with water into a paste and rubbed into the stain.  Soak for a few days and hand wash regularly.

The post How do I remove Tjhoko Paint from clothing or fabric? appeared first on Tjhoko Paint Switzerland.